How to Make a Homecoming Mum
Learn How to Make a Homecoming Mum. For many in the South, and for virtually all Texans, their introduction to the chrysanthemum was a corsage for the girlfriends and mothers at Homecoming football games. Mums are incorporated into elaborate corsages with streamers depicting school colors and special accessories. Corsages can be one, two or three Mums and today silk flowers can be substituted for the real thing.
This is a great project to show school spirit and also for fund raising efforts.
Supplies
Standard incurve chrysanthemum bloom or silk Mum
Cardboard shield or backing
#9, #3, & #1 ribbon matching school colors
Accessories of your choice
Scissors
Hand stapler
Hot glue gun
Instructions
Check out the photos below and follow these instructions.
Preparing Shield/Backing - Part 1
Cut 7 six-inch strips of #9 ribbon (Color A) and 7 six-inch strips of #3 ribbon (Color B)
Cut 6 six-inch strips of #9 ribbon (Color B) and 6 six-inch strips of #3 ribbon (Color A)
Lay a strip of #3 ribbon along a strip of #9 ribbon of the opposite color. The shiny side of both pieces should be facing up. Take the ends of the ribbons between the thumb and forefinger of each hand. Bring the ends together to form a point. Staple the ends together. Continue until all 13 points are made.
Preparing Shield/Backing - Part 2
Staple the points onto a cardboard shield or backing.
With Color A: Position the 7 identical points to form the outside row of points around the shield. Staple the first three points at the 12-, 9-, and 3-o'clock positions. Fill the remaining four points in between the three already positioned.
With Color B: Position the 6 identical points to form the inside row of points around the shield. Fill these points between the points of the outside row.
Preparing Streamers
Using #9 ribbon, cut 10 thirty-inch streamers. (This length can vary depending on the desires of the designer.) Make 5 of the streamers using color A and 5 using color B.
If desired, put lettering on the streamers. Use pre-made letters or make them using glue and glitter.
Cut another 30" streamer of either color A or B. Lay this streamer shiny side up on the table.
Working to the left and alternating colors, lay down 5 streamers. They should overlap at the top and fan out towards the bottom. Staple these together. Follow the same procedure for the remaining streamers. Staple all streamers together.
Staple the streamers onto the shield.
Accessories:
Several accessories can be added to the mum. They include miniature footballs, helmets, bells, etc.
Tie or glue the accessories to strands of #1 ribbon. Vary the length of ribbon strands.
Staple the strands to the backing.
Braided Chains
Braided love chains can be added to the football mum. Two popular types of chains are the two-stranded and three-stranded chains.
Cut a 6� section of ribbon from each of color A and color B. Use #3 ribbon.
Staple the ends of the ribbon together to form an L. One strand should have the shiny side facing upward. The other side should have the dull side facing upward.
Make a loop about 3/4" with the dull strand.
Make a loop of equal size with the shiny strand. Bring this loop through the loop of the dull strand.
Make a loop again with the dull strand and bring it up through the loop of the shiny strand.
Follow this procedure, keeping the strands tight. However do no pull the strands too tight or else the chain will begin bending in an arch.
When completed, staple the ends of the two strands together.
Make a small bow using #3 ribbon. Hot glue the bow onto one end of the chain.
Attach to the streamers.
Making Streamers
Cut 8 six-inch section of #3 ribbon (4 of each color). Staple these together in a radiating manner. Trim the ends on a slant. Hot glue to the top end of the streamers.
Cut 4 twelve-inch sections of #3 ribbon (2 of each color). Staples these together and attach as directed above.
Attaching Flower to Shield
Using a hot glue gun, spread hot glue over the exposed shield. Attach the flower to the shield.
Apply slight pressure until glue has dried.
Making a Large Bow
Using two strands of #3 ribbon (one of each color), make a large bow about the same width of the completed shield.
Glue the bow onto the small streamers, beneath the flower.
Finishing the Backing
Take a 3 1/2-inch section of #9 ribbon. Fold it in half and staple onto another shield. This is where the mum will be attached to the garment.
Glue this second shield onto the back of the corsage shield to cover any staples or mechanics. Be sure to hide any exposed staples so they will not snag the garment of the wearer.
Completing the Mum
Trim streamer tails to make them all even. Notching them in a V-shape improves the overall appearance of the mum.
If desired, lightly spray the entire mum with sparkling glitter.
Other Images
Click on an image to open it in a new window
Contributor
Since 1992, we at Plush in a Rush have dedicated ourselves to the speedy distribution of quality wholesale plush toys, wholesale teddy bears and wholesale stuffed animals. We are a premier source on the web for wholesale plush teddy bears and various wholesale plush animals. We also stock a large variety of wholesale plush toys for babies, birthdays, and other special occasions.
a video of you making it would be lovely – thanks! 🙂
You might try going to the contributor’s website and see if they have one there.
Realized that when we upgraded the site there was a snafu and the illustrations were deleted. We have reposted them. Hope it helps.